Easily check your error code

Samsung · Washer

Samsung Washer 5C Error Code: Not Draining — Causes & Fixes

Also shown as: 5E, SE, SC, nd

5C

5C (5E on older models) means your Samsung washer cannot drain. Samsung says a badly routed or kinked drain hose is the most common reason and service is rarely needed; on front-loaders, a clogged pump filter is next.

Easy⏱ 15–60 minUpdated 2026-11-18

What 5C means

The washer tried to pump water out but the water level did not drop as expected. Samsung uses 5C on newer displays and 5E/SE on older ones for the same drain fault. On UK models the buttons stay disabled for about 3 minutes after the code appears.

Likely causes (most → least common)

  1. Drain hose installed wrongly, kinked or too deep in the standpipeMost common

    Samsung US calls incorrect drain hose installation the most common cause of drain problems. A hose pushed too far into the standpipe, sealed airtight, or squashed behind the machine stops water leaving.

  2. Clogged drain pump filter (front-loaders)Very common

    Lint, coins, hair clips and hair collect in the filter behind the small door at the bottom front. Top-loaders have no user-removable pump filter.

  3. Blocked drain hose or household drainCommon

    Debris inside the hose, or a clogged standpipe/sink trap, can back water up.

  4. Washer not levelOccasional

    Samsung lists levelling as the first check: an unlevel washer may not drain correctly.

  5. Failed drain pump or another internal faultLess common

    If water still does not drain at the start of a test cycle after the checks below, Samsung recommends requesting service.

How to fix it, step by step

  1. Let hot water cool first

    If you just ran a hot or Sanitize-type cycle, Samsung advises waiting about an hour before opening anything, so the trapped water cannot scald you.

    Easy⏱ up to 60 min🔧 No tools
  2. Check the washer is level

    Turn the washer off and check it sits level and does not rock. Adjust the feet if needed.

    Easy⏱ 5 min🔧 Spirit level, Wrench (for the feet)
  3. Inspect the drain hose

    Pull the washer out and straighten any kinks. Samsung US specifies the hose end should sit 6–8 inches into the standpipe, at least 18 inches high (24 inches for a wash basin) and no higher than 96 inches, with no airtight seal and no extension kit. Samsung UK specifies at least 60 cm above the floor and no more than 150 mm inside the standpipe. Do not remove the screw at the back that holds the hose to the washer.

    Easy⏱ 10 min🔧 Flashlight
  4. Clean the pump filter (front-loaders)

    Unplug the washer. Put a towel and a shallow dish in front, open the small access door, pull out the emergency drain hose, remove its cap and let the water run out. Then turn the filter anti-clockwise, remove debris, rinse it in warm water, wipe the recess and screw it back in clockwise until firm.

    Easy⏱ 15–30 min🔧 Towel, Shallow dish or baking tray, Coin (to open some access doors)
  5. Flush the drain hose

    If the hose looks fine from outside, detach it and run water through it to make sure nothing is stuck inside.

    Easy⏱ 10 min🔧 Bucket
  6. Run a test cycle

    Plug the washer back in and start a cycle. It should drain at the beginning. If it does not, request service.

    Easy⏱ 5 min🔧 No tools

When to call a professional

  • The washer still does not drain at the start of a test cycle after the hose and filter checks.
  • You hear the pump hum or grind but no water moves, or you hear nothing from the pump at all.
  • The screw/holder that fixes the drain hose at the back is missing — Samsung says that requires service.
  • Water is leaking from under the machine rather than just not draining.

Parts that may be involved

Always match the part to your exact model number (rating label) before ordering.

Drain pump filter (model-specific)

Replace if the filter housing or thread is cracked and it leaks after cleaning.

Fit: Match your model number; front-load models only.

No price shown — prices are only listed when verified on a retailer page.

Drain pump assembly

Needed only if the pump has failed — usually diagnosed by a technician.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Replacement drain hose

If the old hose is cracked, crushed or permanently kinked.

Fit: Use the length specified for your model; Samsung US advises against hose extension kits.

No price shown — prices are only listed when verified on a retailer page.

Related codes

More Samsung washer codes

Same problem on other brands

All Samsung washer error codes · Every code A–Z

FAQ

How do I reset a Samsung washer 5C error?

Fix the cause first — hose and filter — then turn the washer off and on and start a new cycle. Samsung warns that resetting without troubleshooting lets the error return. On UK models the buttons are locked for about 3 minutes after the code appears.

Is 5C the same as 5E?

Yes. Samsung uses 5C on newer displays and 5E (sometimes shown as SE) on older ones for the same drain problem.

Does a top-load Samsung washer have a pump filter?

No. Samsung notes that top-loaders have no removable pump filter, so for them the hose, the household drain and levelling are the main DIY checks.

Why are the US and UK hose measurements different?

Samsung publishes region-specific installation figures (inches in the US, centimetres in the UK). Use the figure for your region and model — your user manual has the exact values.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.