Easily check your error code

Electrolux · Washer

Electrolux Washing Machine E20 Error Code: Not Draining — Causes & Fixes

Also shown as: E21, C2, 2 beeps / 2 flashes

E20

E20 (also E21, C2, or two beeps/flashes) means your Electrolux washer cannot drain within the expected time. Electrolux says a blocked drain filter is one of the most common causes; also check the drain hose position, height, kinks and your sink trap.

Easy⏱ 20–60 minUpdated 2026-11-18

What E20 means

The washing machine did not pump the water out within its expected time. Electrolux UK groups E20–E24 and C2 as drainage-related codes.

Likely causes (most → least common)

  1. Blocked drain pump / fluff filterMost common

    Lint, coins and small items block the filter or stop the pump impeller turning.

  2. Drain hose kinked or twistedCommon

    Check behind the machine.

  3. Drain hose too deep or at the wrong heightCommon

    Electrolux: hose no more than 10 cm into the drain; drain height between 60 and 100 cm above the base of the machine (or as in your manual).

  4. Blocked sink trap / spigotCommon

    If the machine drains fine into a bucket, the household outlet is the problem.

  5. Program without a drain phaseOccasional

    Electrolux Australia: if you selected a program that ends without draining, set the drain program.

  6. Too much foamOccasional

    Electrolux says heavy foam can block the level system.

  7. Pump overheated after a blockageOccasional

    A thermal (bimetal) fuse switches off a blocked pump; it works again after cooling.

How to fix it, step by step

  1. Run the drain program

    If you used a program without a drain phase, select the drain program.

    Easy⏱ 5 min🔧 No tools
  2. Unplug and drain via the filter

    Unplug. Open the pump door, put a container under it and release water through the emergency drain duct (on many models: press two levers and pull it forward) until no more flows.

    Easy⏱ 15–30 min🔧 Shallow container, Towels
  3. Clean the filter and check the impeller

    Turn the filter counter-clockwise, remove fluff and objects, rinse it under the tap. If the pump blade is visible, turn it with a pencil — it must rotate. Refit the filter tightly to prevent leaks.

    Easy⏱ 10 min🔧 Pencil
  4. Check the drain hose

    Hose no more than 10 cm into the drain, drain height 60–100 cm above the machine base, no kinks or twists. If the hose has been extended, check the joint — Electrolux says it blocks more easily there.

    Easy⏱ 10 min🔧 Tape measure
  5. Test the household drain

    Put the drain hose into a bowl or sink and run a short program. If it drains fine, clear your sink trap or spigot.

    Easy⏱ 15 min🔧 Large bowl or bucket
  6. Let the pump cool and retry

    Electrolux suggests switching off power for about 1–2 hours, then starting a cycle — this lets a pump that cut out on its thermal fuse reset.

    Easy⏱ 1–2 h🔧 No tools
  7. Flush the system

    Run a hot wash without detergent to clean out the drainage system.

    Easy⏱ 1 h🔧 No tools

When to call a professional

  • The pump impeller will not turn after the filter is cleaned.
  • E20 persists after filter, hose and household-drain checks.
  • Water leaks from the filter housing even when the filter is tightened.

Parts that may be involved

Always match the part to your exact model number (rating label) before ordering.

Drain pump filter (model-specific)

Replace a cracked filter or worn seal.

Fit: Match the PNC/model number on the rating plate.

No price shown — prices are only listed when verified on a retailer page.

Drain pump

For a pump that does not turn or run — usually a technician job.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Drain hose

Replace a damaged or permanently kinked hose rather than adding extensions.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Related codes

Same problem on other brands

All Electrolux washer error codes · Every code A–Z

FAQ

What does E20 mean on an Electrolux washing machine?

The machine is unable to drain within the expected time — a drainage problem.

Can a blocked filter cause E20?

Yes, Electrolux says it is one of the most common causes.

Is water in the filter area normal?

A small amount of residual water is normal, according to Electrolux.

When should I book service for E20?

If it still does not drain after cleaning the filter and checking the drain system.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.