Easily check your error code

Samsung · Dishwasher

Samsung Dishwasher LC Error Code: Leak Detected — Causes & Fixes

Also shown as: LE

LC

LC (or LE) means the leak sensor in the base of your Samsung dishwasher detected moisture. The dishwasher keeps running its drain pump to protect your floor. Common causes are hand dish soap, too much rinse aid, a loose hose or a dishwasher tilted forward.

Moderate⏱ 30–90 min + drying timeUpdated 2026-11-18

What LC means

A sensor in the base pan detects water where it should not be. Samsung says the dishwasher then turns itself on, cannot be turned off and keeps trying to drain. On Waterwall models the same code can also mean the water reflector is blocked.

Likely causes (most → least common)

  1. Wrong or too much detergentMost common

    Samsung UK lists hand-washing liquid, too much detergent and an overfilled rinse aid dispenser as leak causes: the foam overflows into the base.

  2. Loose or damaged supply or drain hoseCommon

    A loose supply connection or a hole in either hose drips into the base pan.

  3. Dishwasher leaning forwardCommon

    If the unit tilts forward, water can escape at the door. Samsung recommends levelling it with the three or four feet.

  4. Clogged filterCommon

    A blocked filter makes water back up and overflow.

  5. Blocked Waterwall reflectorModel-specific

    On Waterwall models, a dish or utensil blocking the reflector can trigger the code.

  6. Worn pump gasket, damaged dispenser or tub leakLess common

    Samsung says these require its service centre.

How to fix it, step by step

  1. Switch off and look for water

    Turn the dishwasher off at the breaker (it may keep pumping otherwise). Check the floor, the door edge and the area under the sink for drips or water marks.

    Easy⏱ 10 min🔧 Flashlight, Towels
  2. Check the detergent

    If you used hand dish soap, too much detergent or rinse aid spilled, wipe up the excess (Samsung suggests a wet towel for spilled rinse aid) and switch to a small dose of proper dishwasher detergent.

    Easy⏱ 10 min🔧 Towel
  3. Clean the filter

    Remove the lower rack and the filter at the bottom, rinse it and refit it firmly.

    Easy⏱ 10 min🔧 Soft brush
  4. Check and tighten the hoses

    Under the sink, make sure the supply hose connection is tight and the drain hose is not split. Samsung UK suggests insulation tape only as a temporary measure for a small hole — contact service if it still leaks.

    Moderate⏱ 15 min🔧 Flashlight, Adjustable wrench
  5. Level the dishwasher

    Check side-to-side and front-to-back. If it leans forward, adjust the levelling feet.

    Moderate⏱ 20–30 min🔧 Spirit level, Wrench or screwdriver (model-dependent)
  6. Let the base dry, then test

    The leak sensor stays triggered while the base pan is wet. Leave the power off until any water there has dried out, then restore power and run a short empty cycle while watching for leaks.

    Easy⏱ hours (drying)🔧 No tools

When to call a professional

  • LC comes back after a correct detergent dose, a clean filter and a levelled unit.
  • You find water coming from inside the cabinet (pump, tub or dispenser) rather than from a hose connection.
  • The supply hose leaks even after tightening, or the hose is damaged.
  • No leak is visible but the code persists — Samsung recommends service.

Parts that may be involved

Always match the part to your exact model number (rating label) before ordering.

Dishwasher inlet (supply) hose

Replace a cracked or leaking supply hose.

Fit: Match the connection type and length to your installation.

No price shown — prices are only listed when verified on a retailer page.

Drain hose (model-specific)

Replace if split or punctured.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Filter assembly

If the filter is cracked or will not lock in place.

Fit: Model-specific.

No price shown — prices are only listed when verified on a retailer page.

Related codes

More Samsung dishwasher codes

Same problem on other brands

All Samsung dishwasher error codes · Every code A–Z

FAQ

Why won't my Samsung dishwasher turn off with LC?

That is by design. Samsung says the dishwasher turns itself on and keeps draining while the leak sensor is wet, to protect your floor. Switch it off at the breaker to stop it.

How do I clear the LC code?

Fix the cause, then let the base pan dry completely. Once the sensor is dry, restore power — the code should clear. If it returns, request service.

Can hand dish soap really cause LC?

Yes. Samsung lists hand-washing detergent and too much detergent as causes: the foam overflows into the base and trips the leak sensor.

Is LC the same as LE?

Yes. Samsung uses both codes for the leakage error.

Sources

This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.