LG · Dryer (electric)
LG Dryer d80 Code: Vent About 80% Blocked — Causes & Fixes (Electric Dryers)
Also shown as: D80, d75, d90, d95, Flow Sense
d80 on an LG electric dryer is a Flow Sense airflow warning: the exhaust path is about 80% restricted, usually by lint, a crushed duct or a blocked outside vent. Clean the whole vent run — the code may need several good cycles to clear.
What d80 means
LG's Flow Sense system measures exhaust airflow. d75, d80, d90 and d95 mean roughly 75%, 80%, 90% and 95% restriction. Important: LG notes that on gas dryers d80 can also mean a lack of gas supply — this guide covers electric dryers only; for a gas dryer, contact a qualified technician.
Likely causes (most → least common)
- Lint build-up in the ductMost common
Lint collects in the hose and wall duct, especially at bends.
- Crushed, kinked or damaged exhaust hoseVery common
A hose squashed behind the dryer blocks airflow.
- Blocked outdoor vent hoodCommon
A stuck flap, lint or nesting material at the outside cap.
- Long duct run or many elbowsCommon
LG notes long runs with several bends cause hard-to-find blockages.
- Unsuitable duct materialOccasional
LG says plastic or foil ducting can restrict airflow and trap lint — check your installation instructions.
How to fix it, step by step
Clean the lint filter
Clean the lint filter before every load; it is the first restriction in the airflow path.
Unplug and disconnect the hose
Turn off and unplug the dryer, then carefully detach the exhaust hose from the back.
Inspect hose and wall duct
Look for lint, crushed sections, sharp bends or damage. Replace crushed hose sections.
Remove accessible lint
Brush and vacuum lint from the hose and the accessible wall duct, without pushing it further in.
Check the outside vent
Remove blockages or nesting material from the outdoor cap and make sure the flap opens freely.
Reconnect and test
Reconnect securely, plug in and run a drying cycle. Check outside that air is blowing strongly. If d80 persists, unplug for five minutes and test again — LG says Flow Sense may need several consecutive cycles to reset.
When to call a professional
- The duct runs through walls or ceilings and you cannot reach the whole length — LG recommends a vent-cleaning specialist.
- d80 persists after the full duct has been cleaned and several cycles confirmed good airflow — contact LG support.
- Your dryer is a gas model: d80 can indicate a gas-supply issue; do not attempt gas work yourself.
- You see scorching, smell burning, or the dryer runs very hot.
Parts that may be involved
Always match the part to your exact model number (rating label) before ordering.
Rigid or semi-rigid metal dryer duct
Replaces crushed or plastic/foil hose that restricts airflow.
Fit: Check diameter and the maximum duct length in your manual.
No price shown — prices are only listed when verified on a retailer page.
Dryer vent cleaning brush kit
Reaches lint deep in duct runs and bends.
Fit: LG suggests a 4–8 ft kit; drill-powered kits reach further.
No price shown — prices are only listed when verified on a retailer page.
Outdoor vent hood / flap
Replace a cap whose flap sticks or is broken.
Fit: Match duct diameter.
No price shown — prices are only listed when verified on a retailer page.
Related codes
FAQ
Is d80 an error on an LG dryer?
It is an airflow notification from Flow Sense. The dryer still works, but drying takes longer until the vent is cleaned.
Why is d80 still showing after I cleaned the vent?
LG says Flow Sense may need several consecutive cycles to confirm the improved airflow before it resets. If it stays after the whole duct is clean, contact LG.
What do d75, d90 and d95 mean?
The same warning at different levels: about 75%, 90% and 95% restriction of the exhaust.
Can I turn off the d80 warning?
LG advises against dismissing it — inspect and clean the full exhaust path instead.
Sources
This guide paraphrases the manufacturer's own support documentation. We re-check sources regularly.
- LG Dryer - Error Code List — LG USA Support (last checked 2026-11-18)
- Clearing d80 notification code from display panel — LG Canada (last checked 2026-11-18)